White PLA Filament 1.75mm 1Kg Roll 330 meters per 1kg roll Print Temp:...
Black PLA Filament 1.75mm 1Kg Roll
GT2 timing belt, 6mm wide. Sold per meter length.
608 ZZ Deep Groove Ball Bearing
Idler pulley with 20 teeth
Black ABS Filament 1.75mm 1Kg Roll +-300 meters per 1kg roll Print Temp:...
LM8UU linear bearing
Red PLA Filament 1.75mm 1Kg Roll
LM10UU linear bearing
Yellow PLA Filament 1.75mm 1Kg Roll
Nozzle for E3D V6 Hotend 0.6mm
Resin 3D Printing Service is done via DLP 3d Printer. UV Resin that gets...
Green PLA Filament 3mm 1Kg Roll
Bronze ABS Filament 2.85mm 1Kg Roll
Gold ABS Filament 2.85mm 1Kg Roll
White Flexible TPU 1.75mm 500 Grams
Red Flexible TPU 1.75mm 500 Grams
Green Flexible TPU 1.75mm 500 Grams
E3D V6 Metal hotend PTFE 1.75mm...
E3D V6 Metal hotend PTFE
E3D V6 Metal hotend PTFE
40Watt Heater 12 Volts
30mm 12Volt Fan
+- 1 meter cables
15 Item Items
Warning: Last items in stock!
This E3D V6 Metal Hot End is based on the original E3D V6 Hot End design. This is not the Original E3D Hotend. The V6 hot end is an upgrade from the V5 design. The heaterblock has been improved by clamping the heater cartridge in place and the fixing the thermistor with a small hexagon cap screw. This design is more robust and allows for improved thermal transfer. Another improvement is the V6 hot end is about 10mm shorter in length than the V5 hot end. This allows for higher prints and a more compact look. The E3d Full metal hotend will still fit in the normal V5 hotend clamp.
This hot end is a hybrid between the J-head hot end and the All Metal hot end, because it has the sturdy metal stucture of the All Metal hot end with a cooling fan and the easy to use internal structure of the J-Head hot end with the high temperature PTFE liner. Please note that these hotends have been modified by Uglymonkey for improved print quality. It uses a fan to constantly blow air over the cooling fins to cool down the hot end quickly enough for accurate printing. This is a easy to use, high quality hot end and has been tested with ABS, PLA, Nylon, PC and Flexible filament and up to a temperature of 260 Deg C. This hot end comes with cooling fan, heater cartridge and thermistor.
Note: It is possible that the hot end might leak plastic at the heater block when it is used for the first time. This is because the nozzle was tightened at room temperature and when the hot end is heated up to printing temperature, a small gap is created between the nozzle and the heat break. To solve this, heat the hot end to printing temperature. Hold the heater block with pliers and tighten the nozzle with a 7 spanner, a little bit at a time so that the nozzle seats on the heat break. Please do not force the nozzle otherwise you will strip the heater block. We recommend heating the hotend to about 180 Degrees Celsius, then tighten the nozzle. Careful not to burn yourself.
Always use a shifting or pliers to hold the heater block in place then use a 7 spanner to tighten the nozzle.
No customer reviews for the moment.
Ramps 1.4 Shield B Grade for Arduino Mega 2560
TR 8x2 Lead Screw - 1000mm With Nut Lead Screw...
White PLA Filament 1.75mm 1Kg Roll 330 meters...
Clear Super PLA Filament (Also known as PETG...
GT2 timing belt, 6mm wide. Sold per meter...
10mm 316 Stainless Steel Linear Rods also knows...
Ramps 1.4 Shield for Arduino Mega 2560 This is...
Pneumatic fitting for PTFE Tube 4mm 10mm thread
White Super PLA Filament (PETG) 1.75mm 1Kg...
Arduino Mega 2560 R3 is the perfect micro...